Teledyne-lecroy WaveStation SCPI Command Reference Manual User Manual

WaveStation 2000/3000 SCPI Reference Manual

WaveStation SCPI Header The header is the mnemonic form of the operation to be performed by the oscilloscope. Most headers have a more easily recogniz

Command Reference Numeric values can be followed with multipliers and units modifying the value of the numeric expression. The following table of mn

WaveStation SCPI SCPI Command Reference *IDN? - Identification Query DESCRIPTION The *IDN? query retrieves the instrument’s identification data. Resp

Command Reference *CLS – Clear Status Command DESCRIPTION The *CLS command clears all the status data registers. SYNTAX *CLS RELATED ALL_STATUS,

WaveStation SCPI *RST – Reset Command DESCRIPTION The *RST command initiates a device reset. The *RST sets all eight traces to the GND line and rec

Command Reference *STB? – Status Register Query DESCRIPTION The *STB? query reads the contents of the 488.1 defined status register (STB), and th

WaveStation SCPI ARWV - Arbitrary Wave Command DESCRIPTION Changes the arbitrary waveform type. SYNTAX <channel>:ARbWaVe {INDEX|NAME},<index

Command Reference WaveStation 3000 Arbitrary Waveform Values Index Name Index Name Index Name Index Name Index Name 0 StairUp 8 Sqrt 16

WaveStation SCPI Parameters Value Description MEAN <mean> Parameter is valid only when WVTP is NOISE. Where <mean>:= {default unit is V

Command Reference BTWV - Burst Wave Command DESCRIPTION Sets waveform type to burst or retrieves Burst Wave settings. SYNTAX <channel>:Burs

WaveStation 2000/3000SCPI Reference Manual © 2013 Teledyne LeCroy, Inc. All rights reserved. Unauthorized duplication of Teledyne LeCroy documenta

WaveStation SCPI Parameters Value Description (CARR,)AMP <amplifier> Where carrier wave <amplifier>:= {default unit is V; WS2000 Chann

Command Reference BUZZ - Buzzer Command DESCRIPTION Turns on/off the instrument’s buzzer. SYNTAX BUZZer {ON|OFF} QUERY SYNTAX BUZZer? RESPONSE BU

WaveStation SCPI MDWV - Modulate Wave Command DESCRIPTION Sets a modulated waveform or retrieves current Modulate Wave settings. SYNTAX <channel&g

Command Reference Parameters Value Description (PM,)MDSP <wave shape> Where PM <wave shape>:= {SINE, SQUARE, TRIANGLE, UPRAMP, DNRAMP

WaveStation SCPI QUERY SYNTAX <channel>:MoDulateWaVe? <channel>:= {C1|C2} RESPONSE <channel>:MoDulateWaVe <parameter>,<

Command Reference OUTP - Output Command DESCRIPTION Enables or disables the output connector on the front panel for a specified channel. The query

WaveStation SCPI ROSC - Clock Source Command DESCRIPTION Sets clock source to INTernal system clock or EXTernal clock, or retrieves the current sourc

Command Reference STL? - Store List Query DESCRIPTION Retrieves the names of waveforms saved to WaveStation memory units. If a user-defined memory

WaveStation SCPI Parameters Value Description START <start frequency> Where <start frequency> may be the same as the basic wave freque

Command Reference SYNC - Synchronize Command DESCRIPTION Synchronizes the channel output on the back panel of the instrument to the channel output

Command Reference TABLE OF CONTENTS Introduction to the WaveStation SCPI ...

WaveStation SCPI Name Number Name Number WaveStation 2000 Only KB_SINE 34 KB_ARB 9 KB_SQUARE 29 KB_STORE_RECALL 10 KB_RAMP 24 KB_UP 45 KB_

Command Reference WVCSV - Get .CSV File Command DESCRIPTION Saves a .CSV format waveform file from an outside source to a user-defined memory locat

WaveStation SCPI CHDR - Command Header Command ... 19 INVT -

Command Reference Introduction to the WaveStation SCPI This manual describes the Standard Commands for Programmable Instruments (SCPI) that may be u

WaveStation SCPI Table of Commands & Queries Short Long Subsystem What It Does *IDN? *IDN SYSTEM Retrieves device identification informa

Command Reference Short Long Subsystem What It Does STL STORE_LIST SIGNAL Retrieves all waveform names stored in WaveStation’s device memo

WaveStation SCPI LabView Driver Either the USB or GPIB interface can be utilized with the free LabView Driver to remote control the WaveStation using

Command Reference Program Messages Program messages are composed of commands or queries separated by semicolons. Do not use a terminator of any kind