Teledyne-lecroy LogicStudio User Manual

Getting Started Manual LogicStudio

LogicStudio A 6 922294 Rev A Driver Installation The Wizard then notifies you that the LogicStudio installer contains signed and unsigned drivers. Win

Getting Started Manual B 922294 Rev A 7 The progress of the LogicStudio installation is then shown. The Wizard then lets you know that you can attach

LogicStudio A 8 922294 Rev A The Installation Complete screen is shown. Click the Close button to complete the installation. Now, with correct appli

Getting Started Manual B 922294 Rev A 9 The Waveform Display Area The Waveform Display Area takes up the largest portion of the application display sp

LogicStudio A 10 922294 Rev A Scale and Grid A timescale is displayed along the top edge of the waveform display area at all times. The scale steps an

Getting Started Manual B 922294 Rev A 11 numbered cursor pair. Remove a pair by clicking the Remove Cursor button on the right side of the numbered cu

LogicStudio A 12 922294 Rev A  When placing or moving a cursor over any digital signal, the software looks for any nearby edges on the signal and s

Getting Started Manual B 922294 Rev A 13 The following screenshot shows a cursor pair placed on the waveforms display. RearView™ The RearView™ tool a

LogicStudio A 14 922294 Rev A TIPS:  While using the RearView™ tool, you can modify your signal setup at any time and display additional signals/da

Getting Started Manual B 922294 Rev A 15 WorldView The WorldView is an extremely powerful control just above the waveform display on the dashboard. N

LogicStudio A 16 922294 Rev A end of the bar show the time extent of that data relative to the trigger point. The trigger point itself is denoted by t

Getting Started Manual B 922294 Rev A 17 Run Modes Four run mode buttons are available on the upper-right of the dashboard as follows: The modes Auto

LogicStudio A 18 922294 Rev A a trigger to occur, accumulating a large pre/post-store, or downloading data from an oscilloscope. Signals Control Pane

Getting Started Manual B 922294 Rev A 19 Arranging Your Signals The display of signals can be modified directly through the Signal Control panel as f

LogicStudio A 20 922294 Rev A  Show/Hide – Allows you to remove signals from view without deleting the configuration.  Stacked/Freeform Modes –Th

Getting Started Manual B 922294 Rev A 21 Modifying a Signal Click a signal’s colored name box and corresponding details for the signal are shown on a

LogicStudio A 22 922294 Rev A The Data Table Clicking the Data Table button on the right edge of a given signal (left of the waveform display area) s

Getting Started Manual B 922294 Rev A 23

LogicStudio A 24 922294 Rev A Clicking or using the up/down arrow keys to select a row on the table centers the waveform display timeframe on the sele

Getting Started Manual B 922294 Rev A 25 You cannot make new acquisitions without a connection to a digital pod. However, you do not need to have an o

© 2013 Teledyne LeCroy, Inc. All rights reserved. Unauthorized duplication of Teledyne LeCroy documentation materials other than for internal sales

LogicStudio A 26 922294 Rev A The Signals list allows you to conveniently configure all the signals at the same time. Each row represents a single si

Getting Started Manual B 922294 Rev A 27 NOTE: If you select a different channel mode, the information shown on the left of this setup display is upd

LogicStudio A 28 922294 Rev A different logical ways including: A only, B only, A and B, A or B, A then B, and B then A. The yellow arrows update to

Getting Started Manual B 922294 Rev A 29 Sample Rate The Sample Rate spinner control is located at the top of the dashboard just to the right of the S

LogicStudio A 30 922294 Rev A acquisition file, so trace configurations and other settings will appear the same when the acquisition is loaded as when

Getting Started Manual B 922294 Rev A 31 oscilloscope. Aside from triggering and threshold settings, most LogicStudio features are fully functional an

LogicStudio A 32 922294 Rev A During subsequent program startups, LogicStudio remembers and, if available, auto-connects to the last connected devices

Getting Started Manual B 922294 Rev A 33 TEKTRONIX Support for Tektronix oscilloscopes requires a VISA implementation installed on the PC you’re using

LogicStudio A 34 922294 Rev A Setup Setup functions are accessed under Setup on the menu bar. The setup menu provides alternative access to Signals, I

Getting Started Manual B 922294 Rev A 35 Reference Certifications This section contains the instrument’s Electromagnetic Compatibility (EMC), Safety a

Getting Started Manual B 922294 Rev A i TABLE OF CONTENTS Welcome ...

LogicStudio A 36 922294 Rev A Safety Compliance EC DECLARATION OF CONFORMITY – LOW VOLTAGE The oscilloscope accessory meets intent of EC Directive 20

Getting Started Manual B 922294 Rev A 37 Contact Teledyne LeCroy Teledyne LeCroy Service Centers United States and Canada - World Wide Corporate Offi

Getting Started Manual B 922294 Rev A 1 Welcome Thank you for purchasing a Teledyne LeCroy LogicStudio. This document provides an overview of the Logi

LogicStudio A 2 922294 Rev A Safety Instructions This section contains instructions that must be observed to keep this oscilloscope accessory operatin

Getting Started Manual B 922294 Rev A 3 Operating Environment The accessory is intended for indoor use and should be operated in a clean, dry environ

LogicStudio A 4 922294 Rev A Software Installation The LogicStudio Setup Wizard is then shown. Click Next to proceed with the installation. NOTE: Inc

Getting Started Manual B 922294 Rev A 5 The Confirm Installation screen is shown. Click Next to start your installation.